PREPARATION AND ELECTROCHEMICAL PROPERTIES OF NANOSCALE POROUS CARBON ELECTRODE MATERIALS BASED ON RICE PLANT SOOT

Supercapacitors are a kind of novel energy storage devices with long cycle stability and high power density. Electrode materials selection is one of the key factors that affect the properties of supercapacitors. Biomass-derived electrode materials – being low cost, renewable and environmentally friendly – are therefore attracting researchers’ attention. In this work, we adopted a simple process of carbonization and activation with rice plant soot, a common biomass material, as carbon source, and finally obtained the nanoscale porous carbon electrode (NPCE) materials. Then, the electrochemical properties of the as-prepared NPCE materials were tested in 6 M KOH, and the results indicated that the specific capacitance could reach 216?Fg^?1. Therefore, this low-cost, highly efficient technique is a significant milepost towards environmentally sustainable and commercially feasible fabrication of carbon electrode materials from biomass sources.     

Carbon supported bimetallic Ru‐Co catalysts for H2 production through NaBH4 and NH3BH3 hydrolysis

This work investigates the effect of the addition of small amounts of Ru (0.5‐1 wt%) to carbon supported Co (10 wt%) catalysts towards both NaBH₄ and NH₃BH₃ hydrolysis for H₂ production. In the sodium borohydride hydrolysis, the activity of Ru‐Co/carbon catalysts was sensibly higher than the sum of the activities of corresponding monometallic samples, whereas for the ammonia borane hydrolysis, the positive effect of Ru‐Co systems with regard to catalytic activity was less evident. The performances of Ru‐Co bimetallic catalysts correlated with the occurrence of an interaction between Ru and Co species resulting in the formation of smaller ruthenium and cobalt oxide particles with a more homogeneous dispersion on the carbon support. It was proposed that Ru^°, formed during the reduction step of the Ru‐Co catalysts, favors the H₂ activation, thus enhancing the reduction degree of the cobalt precursor and the number of Co nucleation centers. A subsequent reduction of cobalt and ruthenium species also occurs in the hydride reaction medium, and therefore the state of the catalyst before the catalytic experiment determines the state of the active phase formed in situ. The different relative reactivity of the Ru and Co active species towards the two investigated reactions accounted for the different behavior towards NaBH₄ and NH₃BH₃ hydrolysis.     

Characteristics of Nitric Acid‐Modified Carbon Nanotubes and Desalination Performance in Capacitive Deionization

Multiwalled carbon nanotubes (MWCNTs) were treated by nitric acid to probe the effect of nitric acid modification on their properties and desalination performance in capacitive deionization (CDI). The nitric acid modification exerts a slight influence on the morphologies, specific surface area, and pore properties of the MWCNTs but can increase the amount of oxygen‐containing functional groups and then obviously enhance the specific capacitance of the electrodes. Thus, the desalination efficiency can be significantly improved as the modified MWCNTs serve as electrodes in CDI. The adsorption of salt ions on the original and modified MWCNT electrode is fitted well by the Freundlich isotherm other than the Langmuir isotherm.     

Separation of Methane and Carbon Dioxide Gas Mixtures Using Activated Carbon Modified with 2‐Methylimidazole

Activated carbon was modified by loading 2‐methylimidazole (mIm), ethanol, and glycol onto its surface and adopted to capture CO₂ using the absorption‐adsorption method. The modified activated carbon showed high selectivity for separating CH₄+CO₂ gas mixtures, compared with other methods to modify activated carbon given in the literature. The separation factor was 4.75 times higher than that for the fresh activated‐carbon system, and the separation performance of the activated carbon increased with increasing amount of mIm. The addition of glycol showed greater potential to enhance the selectivity of the activated carbon than ethanol. A recycling test verified the stability of the modified activated carbon for CH₄+CO₂ gas mixture separation.     

New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

Synergistic flame retardant effects of activated carbon and molybdenum oxide in poly(vinyl chloride)

The synergistic effects of activated carbon (AC) and molybdenum oxide (MoO₃) in improving the flame retardancy of poly(vinyl chloride) (PVC) were investigated. The effects of AC, MoO₃ and their mixture with a mass ratio of 1:1 on the flame retardancy and smoke suppression properties of PVC were studied using the limiting oxygen index and cone calorimeter tests. It was found that the flame retardancy of the relatively cheaper AC was slightly weaker than that of MoO₃. In addition, the incorporation of AC and MoO₃ greatly reduced the total heat release and improved smoke suppressant property of PVC composites. When the total content of AC and MoO₃ was 10 phr, PVC/AC/MoO₃ had the lowest peak heat release rate and peak smoke production rate values of 173.80 kW m^?2 and 0.1472 m² s^?1, which represented reductions of 47.3 and 59.9%, respectively, compared with those of PVC. Furthermore, thermogravimetric analysis and gel content tests were used to analyze the flame retardant mechanism of AC and MoO₃, with results showing that AC could promote early crosslinking in PVC. Char residue left after heating at 500 °C was analyzed using scanning electron microscopy and Raman spectroscopy, and the results showed that MoO₃ produced the most compact char, with the smallest and most organized carbonaceous microstructures. © 2017 Society of Chemical Industry     

Morphology,mechanical properties and electromagnetic shielding effectiveness of poly(styrene‐b‐ethylene‐ran‐butylene‐b‐styrene)/carbon nanotube nanocomposites: effects of maleic anhydride,carbon nanotube loading and processing method

Nanocomposites based on poly(styrene‐b‐ethylene‐ran‐butylene‐b‐styrene) (SEBS) and carbon nanotubes (CNTs) (SEBS/CNT) as well as SEBS grafted with maleic anhydride (SEBS‐MA)/CNT were successfully prepared for electromagnetic shielding applications. Both SEBS/CNT and SEBS‐MA/CNT nanocomposites were prepared by melt compounding and were post‐processed using two different techniques: tape extrusion and compression moulding. The different nanocomposites were characterized by Raman spectroscopy and rheological analysis. Their mechanical properties, electrical properties (10^-2–10⁵ Hz) and electromagnetic shielding effectiveness (8.2–12.4 GHz) were also evaluated. The results showed that the CNT loading amount, the presence of MA in the matrix and the shaping technique used strongly influence the final morphologies and properties of the nanocomposites. Whilst the nanocomposite containing 8 wt% CNTs prepared by compression moulding presented the highest electromagnetic shielding effectiveness (with a value of 56.73 dB, which corresponds to an attenuation of 99.9996% of the incident radiation), the nanocomposite containing 5 wt% CNTs prepared by tape extrusion presented the best balance between electromagnetic and mechanical properties and was a good candidate to be used as an efficient flexible electromagnetic interference shielding material. © 2018 Society of Chemical Industry     

Effect of residual excess carbon on the densification of ultra-fine HfC powder

The residual carbon content of ultra-fine hafnium carbide (HfC) powder was controlled by the optimization of the synthesis process, and the effect of residual carbon on the densification of HfC powder was analyzed. The amount of residual carbon in the HfC powder could be reduced by the de-agglomeration of HfO₂ powder before the carbo-thermal reduction (CTR) process. The average particle size of HfO₂ powder decreased from 230 to 130 nm after the de-agglomeration treatment. Ultra-fine (d₅₀: 110 nm) and highly pure (metal basis purity: >99.9 % except for Zr) HfC powder was obtained after the CTR at 1600 °C for 1 h using the C/Hf mixing ratio of 3.3. In contrast, the C/Hf ratio increased to 3.6 without the de-agglomeration treatment, indicating that a large amount of excess carbon was required for the complete reduction of the agglomerated HfO₂ particles. HfC ceramics with high relative density (>98 %) were obtained after spark plasma sintering at 2000 °C under 80 MPa pressure when using the HfC powder with low excess carbon content. In contrast, the densification did not complete at a higher temperature (2300 °C) and pressure (100 MPa) when the HfC powder contained a large amount of residual carbon. The results clearly indicated that residual carbon suppressed the densification of HfC powder in case the carbide powder had low oxygen content, and the residual carbon content could be controlled by the optimization of the synthesis process. The average grain size and Vickers hardness of the sintered specimen were 6.7(±0.7) μm and 19.6 GPa, respectively.     

细菌纤维素合成与鉴定研究综述

细菌纤维素（BC）因其独特性能被广泛应用于医药、食品等领域，目前其高产量菌株筛选、合成成本降低及合成途径改良等成为研究热点。本文依据国内外文献并结合团队研究成果对BC合成与鉴定的相关研究进行综述。首先对BC合成菌筛选及碳源利用的研究进行了分析，总结了降低BC合成成本的研究思路。其次对鉴定菌株合成产物的方法进行了归纳，总结了不同方法的特点。然后结合本团队筛选出的BC生产菌XJL-06-4 BC合成酶基因分析结果，综述了BC合成途径、合成酶存在形式以及基因水平调控作用，为BC在分子水平上通过改变合成途径提高产量提供新思路。最后，总结BC微生物发酵生产存在的问题，多角度提出解决方案。